Skip to main content

RC Transmitter Reciver

 RC Transmitter Reciver

This transmission range 1.5KM just 250/-useful components NRF24L01 module with antenna. 

Using microcontroller atmel company

At mega series Atmega8A for Transmitter

For receiver circuit NRF24L01 module without extranal antenna. Using microcontroller for receiver atmel company atmega series Atmega 328P .

Programming upload ISP PIN using Arduino nano you can use ISP tool .

Programming IDE software Arduino IDE , Visual Studio Code or any other software.

NRF24L01 module supply +3.3V constant
Or microcontroller supply +5V constant . Joystick Value 0 to 255 middle value 127 with 0/1 switch.

Full Circuit or Code Comming soon.


Popular posts from this blog

Fm transmitter circuit

Fm transmitter circuit Power supply   :-   Using power supply stable DC voltage 2V to 3.7V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components  :- Transistor BC547, Resistance 100 ohms, 4.7K ohms.   Capacitor 1nF, 47pF, 22pF.   Inductor 1uH. Condenser mic any. Resistance  :-   Using resistance 100 ohme +-5% changing 1/3watt, 4.7K ohms +-5% changing 1/3watt. Capacitor  :-   1nF this capacitor number 102 non-polar, 22pF this capacitor number 22 non-polar, 47pF this capacitor number 47 non-polar. Inductor  :-   This part important part for any transmitter circuit, 1uH 5Turn 24SWG. Transistor  :-   BC547  is an NPN Bipolar junction transistor. It is commonly  used  to amplify current. A small current at its base controls a larger current at collector & emitter terminals.  It has a transition  frequency range  up to 100 MHz. When using the transistor as a switch, the max current rating p

MW transmitter using Arduino nano

MW transmitter using Arduino nano Circuit Diagram MW frequency :-   Medium wave is the part of the medium frequency radio band used mainly for AM radio broadcasting. The spectrum provides about 120 channels with limited sound quality. During daytime, only local stations can be received. Code _____________________________________________ #define ANTENNA_PIN PB3 void setup() { Serial.begin(115200); uint32_t fTransmit = 600; DDRB |= (1 << ANTENNA_PIN); TCCR2A = (0 << COM2A1) + (1 << COM2A0); TCCR2A |= (1 << WGM21) + (0 << WGM20); TCCR2B = (0 << CS22) + (0 << CS21) + (1 << CS20); OCR2A = F_CPU / (2000 * fTransmit) - 1; char strbuf[255]; sprintf(strbuf, "Will broadcast at %d KHz", (F_CPU / (2 * (1 + OCR2A)) / 1000)); Serial.println(strbuf); TCCR1A |= (1 << WGM11) + (1 << WGM10); TCCR1B = (1 << WGM12); TCCR1B |= (0 << CS12) + (0 << CS11) + (1 << CS10);

FM transmitter using crystal

FM transmitter using crystal  Video link - 3Volt circuit digram  5Volt circuit digram This Transmitter range 300 metre to 500 metre without any obstacle otherwise range 200 anywhere. It's a spy device. Discuss about listing components Used transistor BC547 for oscillator and I'm using crystal for noise clear frequency and it is very stable frequency.  I am using crystal 25MHz. Using 1K ohms resistance for safe collector transistor overheating. Using 4.7K ohms resistance for active mic .